The HM-19 makes use of TI’s CC2640R2F chip because the grasp IC.

In comparison with HM-11, HM-19 is a Bluetooth 5.0 BLE module,it has a sooner switch fee and a bigger MTU.

This module can be utilized not just for DIY undertaking, but additionally in your merchandise.

Authentic HM-19 module, DSD TECH model ensures and that we settle for refund with none excuse..
Bluetooth 5.0 BLE Module: essentially the most IC is CC2640R2F from TI,In comparison with the Bluetooth 4.0 module, this module incorporates a sooner switch fee and a much bigger MTU.

DSD TECH 6 PIN base Board: ends in VCC, GND, TX, RX,STATE,EN. You may be very handy to connect to your arduino undertaking or different DIY undertaking.

DSD TECH provides a free app that means that you can rapidly combine this module into your undertaking.Please search “DSD TECH Bluetooth” in Google Play and due to this fact the Appstore.

The HM-19 is an upgraded model of the HM-11. The HM-19 makes use of TI’s CC2640R2F chip as a result of the grasp IC.

In comparison with HM-11, HM-19 could also be a Bluetooth 5.0 BLE module,it has a sooner switch fee and a much bigger MTU.

This module are sometimes used not only for DIY undertaking, but additionally in your merchandise.
Its Work voltage(VCC): 3.6V to 6V and TTL logic stage (TX, RX): 3.3V, Helps Bluetooth protocol: 5.0 BLE and Chip: TI CC2640R2F. Its fundamental mode helps two working modes: automated working and guide working.

The AT instructions of the HM-19 module are appropriate with the AT instructions of the HM-11 and HM-10 module.

HM-19 Bluetooth 5.0 Clear interface Grasp-Slave Module CC2640 MCU Hello Pace appropriate with HM-11 HM-13 HM-17.

DSD TECH again this HM-19 Bluetooth 5.0 BLE module with ONE Yr WARRANTY and lifelong technical assist.

The sooner hm-19 present model V103 helps the following options:
Transmission mode, transmission + distant twin operation mode.The primary mode helps automated work and guide work.Extremely-high transmission velocity (BLE as much as 8KB/S). Considerable AT instruction, supporting native serial AT instruction and distant AT instruction and Tremendous MTU 253Bytes. It Help iBeaon operate and firmware improve.

It’s included with 4.2 and 5.0, default 2M bandwidth connection, appropriate with 1M bandwidth.

Product Parameters:HM 19 Bluetooth Module

• BT Model: Bluetooth Specification V4.2 BLE
• Ship and obtain no bytes restrict.
• Working frequency: 2.4GHz ISM band
• Modulation technique: GFSK(Gaussian Frequency Shift Keying)
• RF Energy: -18dbm ~ 3dbm, may be modify via AT Command AT+POWE.
• Pace: Asynchronous: 1-8K Bytes
• Synchronous: 1-8K Bytes
• Safety: Authentication and encryption
• Service: Central & Peripheral
• FFE0 is service UUID (may modify by AT+UUID command)
• FFE1 is Char1 UUID (may modify by AT+CHAR command)
• Default property : Learn, Write With out Response, Notify Property may modify by AT+RESP command
• FFE2 is Char2 UUID (May open by AT+FFE2 command)
• In case you use AT+CHAR command to alter Char1 worth, then Char2 worth shall be Char1 worth + 1.
• Energy: +1.9~5.5 VDC 50mA
• Lengthy vary: Open area have 100 Meters vary
• Energy: Low Energy Mode 50uA~500uA, Standby mode 6mA, Lively mode 10mA.
• Working temperature:–40 ~ +85 Centigrade
• Dimension: HM-18 27mm * 13mm * 2.2 mm
• Dimension: HM-19 18mm * 13mm * 2.2mm

The post HM 19 Bluetooth Module appeared first on Dilson Enterprises.

The HM-18 is an upgraded model of the HM-10. The HM-18 makes use of TI’s CC2640R2F chip as a result of the grasp IC. The HM-18 makes use of TI’s CC2640R2F chip as a result of the grasp IC.

In comparison with HM-10, HM-18 could also be a Bluetooth 5.0 BLE module,it has a quicker switch charge and a bigger MTU. In comparison with HM-10, HM-18 could also be a Bluetooth 5.0 BLE module,it has a quicker switch charge and a bigger MTU. Specs Work voltage?VCC?: 3.6V to 6V TTL logic degree (TX, RX): 3.3V Bluetooth protocol: 5.0 BLE Chip: TI CC2640R2F PIN: VCC,GND,TX,RX The AT instructions of the HM-18 module are suitable with the AT instructions of the HM-10 module. Precautions: Bluetooth 5.0 BLE module is not suitable with any Bluetooth 2.0 SPP machine About Take a look at APP DSD TECH presents a free app that lets you rapidly combine this module into your challenge. For android, Please search “DSD TECH Bluetooth” in Google Play. For iOS Gadgets(iPhone) ,Please search “DSD TECH Bluetooth” inside the App Retailer WARRANTY We again this HM-18 Bluetooth 5.0 BLE module with ONE YEAR WARRANTY. In case you meet any query, please contact us, we’ll repair your difficulty inside 24 hours.

HM 18 Bluetooth module use CYPress IC, Grasp and slave roles in a single, transmission model and distant model in a single, Help the AT command modify module parameters, Handy and versatile . Transmission model are sometimes wont to transmit knowledge between two Bluetooth gadgets. Distant Management model are sometimes wont to Management PIO ports output excessive or low degree with none different MCU.
Its Working frequency: 2.4GHz ISM band and Modulation technique: GFSK (Gaussian Frequency Shift Keying.

RF Energy: -18dbm ~ 3dbm, are sometimes modify via AT Command AT+POWER and its Velocity: Asynchronous: 1-8K Bytes. Its Safety: Authentication and encryption and it offers Service: Central & Peripheral UUID FFE0, FFE1.

Included with Energy: +1.9~5.5 VDC 50mA and has a Lengthy vary: Open area have 100 Meters vary.

Its Energy: Low Energy Mode 50uA~500uA, Standby mode 6mA, Energetic mode 10mA.
Working temperature:–40 ~ +85 Centigrade.

FEATURES: HM 18 Bluetooth Module

• BT Model: Bluetooth Specification V4.1 BLE Ship and obtain no bytes restrict.
• Working frequency: 2.4GHz ISM band
• Modulation technique: GFSK (Gaussian Frequency Shift Keying)
• RF Energy: -18dbm ~ 3dbm, could be modify via AT Command AT+POWER.
• Velocity: Asynchronous: 1-8K Bytes
• Safety: Authentication and encryption
• Service: Central & Peripheral UUID FFE0, FFE1
• Energy: +1.9~5.5 VDC 50mA
• Lengthy vary: Open area have 100 Meters vary
• Energy: Low Energy Mode 50uA~500uA, Standby mode 6mA, Energetic mode 10mA.
• Working temperature:–40 ~ +85 Centigrade
• Measurement: 27mm * 13mm * 2.2 mm

The post HM 18 Bluetooth Module appeared first on Dilson Enterprises.

The HM-17 is an improved model of the HM-11. The HM-17 makes use of the CC2640R2F chip from TI as a grasp IC.In comparison with HM-11, HM-17 could also be a Bluetooth 4.1 module, it is a sooner switch fee and a much bigger MTU.This module are sometimes used not simply on your digital manufacturing, but in addition on your merchandise.

Working Voltage (VCC): 3.6V ~ 6V
TTL logic degree (TX, RX): 3.3 V

Probably the most full, most handy, the foremost steady of bluetooth knowledge transmission, distant , PIO acquisition Hm 17 module supoorts Grasp and slave function in a single: Distant management with out different MCU; The PIO knowledge acquisition with out different MCU. HM-17-2640 model is BLE 4.2 protocol, supporting firmware improve, present model V109/V110, help BLE5.0 improve, pin suitable with hm-11, hm-13.

The primary capabilities of HM 17 module includes- essentially the most capabilities of the module are as follows:
Grasp and slave,Transmission operate and Transmission by means of + distant operate. it is integrated with Tremendous massive transmission unit (MTU)/Package deal. it is Plentiful AT command system and it Help modification service UUID. It additionally Help the modification of communication mode, iBeacon and Help hibernation and standby.

It might probably cowl a wide range of Extremely-long distance communication, as much as 40-100 meters in superb atmosphere with Sooner transmission velocity, 2~8KB/S. Most AT instruction techniques are suitable with hm-10 / hm-11. Help common studying operate, which can join and be taught BLE modules of different manufacturers throughout the market (with out password).

It’s AT command system suitable HM-10 / HM-11 with Functions: Distant controller, wi-fi communication.

Hm 17 bluetooth module Helps common studying operate, you may join and be taught from different manufacturers of BLE modules in the marketplace (with out password).

Product parameters:HM 17 Bluetooth Module

• BT Model: Bluetooth Specification V4.2 BLE
• Ship and obtain no bytes restrict.
• Working frequency: 2.4GHz ISM band
• Modulation technique: GFSK(Gaussian Frequency Shift Keying)
• RF Energy: -18dbm ~ 3dbm, will be modify by means of AT Command AT+POWE.
• Pace: Asynchronous: 3-8K Bytes
• Safety: Authentication and encryption
• Service: Central & Peripheral
• FFE0 is service UUID (might modify by AT+UUID command)
• FFE1 is Char1 UUID (might modify by AT+CHAR command) Default property : Learn, Write With out Response, Notify Property might modify by AT+RESP command
• FFE2 is Char2 UUID (Might open by AT+FFE2 command) If you happen to use AT+CHAR command to vary Char1 worth, then Char2 worth might be Char1 worth + 1.
• Energy: +1.9~3.7 VDC 50mA
• Lengthy vary: Open area have 100 Meters vary
• Energy: Standby mode 2.6mA, Energetic mode 2.6mA.
• Working temperature:–40 ~ +105 Centigrade
• Dimension: HM-16 27mm * 13mm * 2 mm
• Dimension: HM-17 18mm * 13mm * 2mm

The post HM 17 Bluetooth Module appeared first on Dilson Enterprises.

HM-16 CC2640R2F Bluetooth Module is a wi-fi Bluetooth 4.2 BLE module, which is designed primarily based on CC2640R2F SimpleLink Bluetooth® low power Wi-fi MCU chip. This chip is a wi-fi microcontroller that gives a low energy Bluetooth® 4.2- and Bluetooth 5 module for transportable and battery equipped functions. The SimpleLink CC26xx collection characteristic ultra-low-power and cost-effective 2.4-GHz wi-fi chip. The CC2640R3F chip has a 32-bit ARM® Cortex® -M3 CPU core for the primary processing and a wealthy peripheral characteristic set with a devoted ultra-low-power sensor controller. This sensor controller can interface with exterior sensors to gather analog and digital knowledge stand-alone whereas resting the system in sleep mode. Thus, the CC2640R2F can extensively be utilized in such functions which have constraints of battery lifetime, house, and ease of use.

HM 16 Bluetooth module use CYPress IC, Grasp and slave roles in a single, transmission model and distant management model in a single, Help the AT command modify module parameters, Handy and versatile. Transmission model can be utilized to transmit knowledge between two Bluetooth gadgets. Distant Management model can be utilized to Management PIO ports output excessive or low stage with out another MCU.

This module is an HM collection, that use CYPress IC, Grasp and slave roles collectively, transmission and distant management model collectively and helps iBeacon, the AT command and modifying the service UUID and the communication methodology. The HM collection is began with HM1 and this module is the sixteenth model of this household. the HM-16 module has 128Kbit flash reminiscence and will be equipped with 1.9V as much as 5.5V DC to attain extremely long-distance about 110m Bluetooth wi-fi communication V4.2 BLE by a low dimension PCB with about 267mm x 13mm x 2.2mm.

HM 16 Bluetooth know-how manages the communication channel of the wi-fi half. The Bluetooth modules can transmit and receives the info wirelessly through the use of two gadgets. The Bluetooth module can obtain and transmits the info from a bunch system with the assistance of the host controller interface (HCI).

FEATURES:HM 16 Bluetooth Module

• BT Model: Bluetooth Specification V4.1 BLE Ship and obtain no bytes restrict.
• Working frequency: 2.4GHz ISM band
• Modulation methodology: GFSK (Gaussian Frequency Shift Keying)
• RF Energy: -18dbm ~ 3dbm, will be modify via AT Command AT+POWER.
• Velocity: Asynchronous: 1-8K Bytes
• Safety: Authentication and encryption
• Service: Central & Peripheral UUID FFE0, FFE1
• Energy: +1.9~5.5 VDC 50mA
• Lengthy vary: Open house have 100 Meters vary
• Energy: Low Energy Mode 50uA~500uA, Standby mode 6mA, Lively mode 10mA.
• Working temperature: –40 ~ +85 Centigrade
• Dimension: 27mm * 13mm * 2.2 mm

The post HM 16 Bluetooth Module appeared first on Dilson Enterprises.

Working voltage 3.6 V to 6V,Default baud price is 115200. The HM-13 is totally appropriate with the HM-11 module.

The Bluetooth Mate 4.0 is that the subsequent evolution in our line of serial Bluetooth modules. This board is supplied with an HM-13 module, which helps each SPP (Serial Port Profile) and BLE (Bluetooth low-energy) Bluetooth profiles by way of Bluetooth 4.0.

This board’s HM-13 Bluetooth module helps each SPP (Serial Port Profile) and BLE (Bluetooth low-energy) Bluetooth profiles by way of Bluetooth 4.0. The HM-13’s assist for BLE means it’s appropriate with any smartphone. Or you possibly can join it to a pc by way of the previous normal — SPP — and use it as a clear Bluetooth information gateway. You possibly can even use it in dual-mode, related to a pair of gadgets concurrently!

This board consists of all the voltage regulating and degree shifting you wish to interface both 5V or 3.3V microcontrollers with the Bluetooth module. Communication with the HM-13 is carried out by a serial UART, and an AT-command construction is employed to configure it.

Along with the power-indicator LED, there is a inexperienced “CON” LED. When the module is disconnected, this LED will blink at 1Hz; when it’s related, the LED are going to be solidly on. Its Modulation technique: GFSK (Gaussian Frequency Shift Keying) with Working temperature: –5 ~ +65 Centigrade and Energy: SPP 13.5mA, BLE 9.5mA.

HM 13 has two information transmission mode, stability mode and excessive pace mode.

Product Parameters:HM 13 Bluetooth Module

• BT Model: Bluetooth Specification V4.0 & BLE
• UART ship and obtain max bytes is 512.
• Different system to module in SPP mode: 60 Bytes per packet
• Different system to module in BLE mode: 20 Bytes per packet.
• Two information transmission mode, stability mode and excessive pace mode.
• Working frequency: 2.4GHz ISM band
• Modulation technique: GFSK(Gaussian Frequency Shift Keying)
• RF Energy: -23dbm, -6dbm, 0dbm, 6dbm.
• Velocity: Asynchronous: 2-6K Bytes
• Synchronous: 2-6K Bytes
• Safety: Authentication and encryption
• Service: Slave SPP, Peripheral BLE, UUID FFE0,FFE1
• Energy: +3.3VDC 50mA
• Lengthy vary: SPP 30 meters, BLE 60 meters.
• Energy: SPP 13.5mA, BLE 9.5mA.
• Working temperature:–5 ~ +65 Centigrade
• Measurement: HM-12 27mm x 13mm x 2.2 mm;
• Measurement: HM-13 18 x 13 x 2.2mm

The post HM 13 Bluetooth Module appeared first on Dilson Enterprises.

HM-12T has ultra-high transmission velocity (EDR can ship at full fee of interface, BLE as much as 8KB/S.
Its Serial buffer measurement: 512 Bytes and Begin time: steadiness mode 1.2 seconds, excessive velocity mode 1 second
It operation Working mode: balanced mode, excessive velocity mode and might Transmit obtain distance: SPP 30m, BLE 60m

Working mode: automated energy on reset, RESETB pin are sometimes left clean It’s included with Working frequency: 2.4GHz ISM band and Modulation mode: GFSK (Gaussian Frequency Shift Keying). Its Sensitivity =-84dBm at 0.1% BER and transmission velocity: SPP 90%, BLE 40%
Its Security traits: Authentication and encryption together with EDR service: L2CAP, SDP, RFCOMM, SPP and BLE service: ATT, GATT, LE Service: OxFFE0, Char: OxFFE1. This machine has a Energy wastage of about 20mA, stand-by t10-17mA and Energy provide: 3.3 VDC 50mA. Its working temperature: -5 ~ 80 Centigrade and Look measurement: 27*13*2.2mm.

The module has built-in wifi community protocol and BLE Bluetooth protocol stack, which may understand quick distribution community via BLE. It’s extremely suited to ultralow energy consumption programs. The module is little and simple to make use of, with the preprogramed firmware of producer, you may rapidly construct BLE communications through it’s AT command.

The communication between controller and module is mainly advanced. We’ll use libraries written for particular controller or boards to talk with this module.

The module is often linked to +3.3V customary energy provide. It might work on +3.6V regulated energy and any greater voltage might harm the module. The UART interface is established as proven in determine. All you wish to attempt to to is join RX of module to RX of controller and TX is linked to TX of controller. The bottom of controller and module have to be linked for voltage reference.

Kind: HM-12T
Measurement: 13 * 27 * 2.2 mm
BT Model: V4.0 EDR & BLE
Firmware: V116
Standing: In manufacturing

The post HM 12T Bluetooth Module appeared first on Dilson Enterprises.

IF you’re in want of such a 4.0 BLE Bluetooth module, MCU might be arrange,can also managed by a distant Bluetooth system for setting,can switch knowledge, and might remotely management 10 PIO pins,so,your best option is HM-10/11 bluetooth module.

The HM-11 Bluetooth 4.0 BLE Module relies on TI cc2541 chip, permits sturdy community nodes to be constructed with low complete bill-of-material prices and extremely fitted to ultralow energy consumption techniques. It’s extremely fitted to ultralow energy consumption techniques. The module is little and simple to make use of, with the preprogramed firmware of producer, you will shortly construct BLE communications by way of it’s AT command. Supporting BLE communications with iPhone, iPad and Android 4.3.

Transmission energy: – DBM, 23-6 DBM, 0 DBM, 6 DBM, are sometimes modified by the AT command and it makes use of TI CC2541 chip, configuration house of 256 KB, assist the AT command, the consumer can per obtained to alter the function (grasp, slave mode) and subsequently the interface baud , title of equipment , matching parameters like passwords, use agile. It helps serial interface with Working frequency: 2.4 GHz ISM band.

Transmission model are sometimes wont to transmit knowledge between two Bluetooth gadgets. distant model are sometimes wont to Management PIO ports output excessive or low stage with out every other MCU.

The PIO state acquisition model are sometimes wont to acquisition PIO ports state with out every other MUC. (Solely assist Bluetooth V2.1)

With the utilization of HM 11 the consumer can per obtained to alter the function (grasp and slave mode) and subsequently the serial baud , gear title, pairing password parameters and versatile to make use of. HM-11 from one module, with clear transmission, distant, PIO collected three types of capabilities, and set the change by means of the AT instruction setting.

IF you are in want of such a 4.0 BLE Bluetooth module, MCU are sometimes discovered ,can also managed by a overseas Bluetooth system for setting,can switch knowledge, and might remotely management 10 PIO pins,sothe best option is HM-10/11 Bluetooth module. HM-11 dimension is merely have 2.4cm X1.5cm.

It supplies an Open atmosphere inside 60m (100ft) can understand communication between modules and its Response velocity as much as 0.4s .To ship and obtain no byte restrict between modules, as much as 6KB/s and its Extremely low standby energy consumption: 400uA-800uA.

The post HM 11 Bluetooth Module appeared first on Dilson Enterprises.

If you’re in want of such a 4.0 BLE Bluetooth module, MCU might be arrange, can also managed by a distant Bluetooth gadget for setting, can switch knowledge, and may remotely management 10 PIO pins,so,the only option is HM-10 bluetooth module.

It Helps Distant management mode, distant gadget can management PIO pin or modify settings by AT commander when Related. (Resembling Iphone4s/5 ipad, Note2 and so forth.) and Help Central and Peripheral mode change, modify by AT commander.

The HM-10 Bluetooth module combines the highly effective and programmable Texas Devices CC2541 Chipset with the desired parts to begin out straight collectively along with your BLE improvement.The module gives an on-board voltage regulator and is TTL-level and 5 V tolerant. The Bluetooth-SoC are sometimes accessed through UART interface and helps AT-Instructions for setup. It helps full Bluetooth 4.0 commonplace and could also be used in your Arduino or microcontroller to Android or iOS communication tasks.This module are sometimes wont to exchange HC-05, HC-06 and HC-07 gadgets.This module additionally might be configured and used as an iBeacon for used with Apple gadgets.

It’s absolutely configurable by an upscale and properly documented AT command-set and permits clear digital communication through serial UART (default baud 9600bps). The Bluetooth 4.0 HM-10 is basically a breakout board for cc2541, it broke out the LED pins, RX/TX and in addition including the transformer that common 5v to a few .3 v.

HM-10 and HM-11 collection Bluetooth module use TI CC2540 chip, configure 256KB house and assist the AT command. Customers can change the function (grasp, slave mode) and subsequently the interface baud , gear title, matching password and different parameters on-demand. It is vitally versatile to make use of.
Probably the most full, most handy, and most secure Bluetooth knowledge transmission, distant and knowledge acquisition module. Grasp-slave in a single, clear transmission, changing the interface . Distant management, clear transmission, MCU is pointless. Distant knowledge acquisition, clear transmission, MCU is pointless.

SPECIFICATIONS:

• BT Model : Bluetooth Specification V4.0 BLE
• Ship and obtain no bytes restrict.
• Working frequency : 2.4GHz ISM band
• Modulation methodology : GFSK(Gaussian Frequency Shift Keying)
• RF Energy : -23dbm, -6dbm, 0dbm, 6dbm, can modify by means of AT Command AT+POWE.
• Pace : Asynchronous 6K Bytes
• Synchronous : 6K Bytes
• Safety : Authentication and encryption
• Service : Central & Peripheral UUID FFE0,FFE1
• Energy : +3.3VDC 50mA
• Lengthy vary : Open house have 100 Meters with iphone4s
• Energy : In sleep mode 400uA~1 .5mA, Lively mode 8.5mA.
• Working temperature : –5 ~ +65 Centigrade
• Measurement : 26.9mm x 13mm x 2.2 mm.

The post HM 10 TTL BLE Bluetooth Module (Unique) appeared first on Dilson Enterprises.

The Bluetooth-SoC are sometimes accessed by way of UART interface and helps AT-Instructions for setup. It helps full Bluetooth 4.0 normal and can be utilized on your Arduino or microcontroller to Android or iOS communication tasks.

In case you’re in want of such a 4.0 BLE Bluetooth module, MCU are sometimes discovered , also can managed by a overseas Bluetooth gadget for setting, can switch information, and might remotely management 10 PIO pins,so the only option is HM-10 Bluetooth module.

Assist distant mode, distant gadget can management PIO pin or modify settings by AT commander when Linked. (Comparable to Iphone4s/5 ipad, Note2 and so forth.)

HM TTL Module Assist Central and Peripheral mode swap, modify by AT commander Bluetooth module use CSR BlueCore or TI CC2540, Grasp and slave roles in a single, transmission model and distant management model and PIO stateacquisition features in a single, Assist the AT command modify moduleparameters, Handy and versatile .Transmission model are sometimes wont to transmit information between two Bluetoothdevices.

Distant Management model are sometimes wont to Management PIO ports output excessive orlow degree with none different MCU.The PIO state acquisition model are sometimes wont to acquisition PIO ports state with out every other MUC. (Solely help Bluetooth V2.1)HM-01, HM-02, HM-03, HM-04, HM-05, HM-06, HM-07, HM-08, HM-09 isBluetooth V2.1 model. Use CSR Chip. Excessive-performance TI CC2541 Bluetooth Low Vitality SOC constructed andEasy to make use of due to 5 V/TTL publicity degree Tolerant inputs. It isConfigurable with at instructions per UART

Supreme for wi-fi communication between Arduino or Micro controllers and Android or iOS units
Working voltage: 5 V, modes: Grasp/Slave (adjustable), baud price: 9600 – 115200 (adjustable), Interface: UART, Bluetooth 4.0. It may Ship and obtain no bytes restrict.

Its Working frequency: 2.4GHz ISM band and Modulation technique: GFSK(Gaussian Frequency Shift Keying). Included with RF Energy: -23dbm, -6dbm, 0dbm, 6dbm, can modify by way of AT Command AT+POWE.

Its Velocity : Asynchronous : 6K Bytes and Synchronous : 6K Bytes

HM BLE TTL module Energy vary : +3.3VDC 50mALong vary : Open house have 100 Meters with iphone4s

Energy : In sleep mode 400uA~1 .5mA, Lively mode 8.5mA.Included with Working temperature: –5 ~ +65 Centigrade and Measurement : HM-10 26.9mm x 1 3mm x 2.2 mm.
Product Particulars:

The post HM 10 TTL BLE Bluetooth Module appeared first on Dilson Enterprises.

The HM-10 makes use of the customized attribute to ship and obtain the information it receives over the serial UART interface. It really works by setting the price of the customized attribute to the price of the information to be transmitted. It then sends out a notification to the distant machine to say there’s new information obtainable.

Once you inform the the HM-10 to transmit “HELLO”, it first units the price of the customized attribute to “HELLO” then it sends out a notification telling the distant machine “Hey, I even have new information, come and acquire it.” The distant machine is scanning for the notifications and when it receives one it is aware of there is a substitute worth, so it reads the information then sends again a message saying “Thanks, I even have it”.

The customized attribute can delay to twenty characters, this implies to ship a string longer than 20 characters the HM-10 splits the information in to twenty character segments and sends every one in flip till none are left.

HM 10 Bluetooth module use CSR BlueCore or TI CC2540, Grasp and slave roles in a single, transmission model and distant model and PIO state acquisition features in a single, Assist the AT command modify module parameters, Handy and versatile.

Transmission model are sometimes wont to transmit information between two Bluetooth gadgets. Distant Management model are sometimes wont to Management PIO ports output excessive or low degree with none different MCU.

Specification:HM 10 BLE Core Bluetooth Module

• BT Model: BT Specification V4.0 BLE
• Working frequency: 2.4GHz ISM band
• Modulation methodology: GFSK (Gaussian Frequency Shift Keying)
• RF Energy: -23dbm, -6dbm, 0dbm, 6dbm
• Pace: Asynchronous: 2-6K Bytes, Synchronous: 2-6K Bytes
• Safety: Authentication and encryption
• Service: 0xFFE0 (Modifiable use AT+UUID command)
• Attribute: 0xFFE1 (Modifiable use AT+UUID command)
• Attribute: Notify and Write (Modifiable use AT+UUID command)
• Energy: +2.5V~3.5VDC 50mA
• Energy: Lively state 8.5mA; Sleep state 50~200uA
• Working temperature: –20 ~ +105 Centigrade
• Dimension: HM-10 27mm x 13mm x 2.2 mm

The post HM 10 BLE Core Bluetooth Module Authentic appeared first on Dilson Enterprises.