E-Paper 2.9″ Show Module
This is an E-Ink display module, 2.9inch, 296×128 resolution, with embedded controller, communicating via SPI interface, supports partial refresh.
Features: E -Ink Display Module 2.9 inch
- No backlight, keeps displaying last content for a long time even when power down
- Ultra low power consumption, basically power is only required for refreshing
- SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc.
- Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)
Package Includes: E -Ink Display Module 2.9 inch
- 2.9 inch e-Paper Module x1
- PH2.0 20cm 8Pin x1
Application: E -Ink Display Module 2.9 inch
- Education: Digital school books
- Wristwatches
- E-Books
- Newspaper
- Cell phones
- Status display
Description
Overview
That is an E-Ink show module, 2.9inch, 296×128 decision, with embedded controller, speaking through SPI interface, helps partial refresh.
As a result of benefits like extremely low energy consumption, vast viewing angle, nice impact below daylight, it is a perfect selection for purposes resembling shelf label, industrial instrument, and so forth.
Specs:
- Working voltage: 3.3V/5V
- Interface: 3-wire SPI, 4-wire SPI
- Define dimension: 89.5mm × 38mm
- Show dimension: 66.89mm × 29.05mm
- Dot pitch: 0.138 × 0.138
- Decision: 295× 128
- Show colour: black, white
- Gray degree: 2
- Full refresh time: 2s
- Partial refresh time : 0.3s
- Refresh energy: 26.4mW(typ.)
- Standby energy: <0.017mW
- Viewing angle: >170°
Interface
| Image | Description |
|---|---|
| VCC | 3.3V |
| GND | Floor |
| DIN | SPI MOSI pin |
| CLK | SPI SCK pin |
| CS | SPI chip choice, low lively |
| DC | Knowledge/Command choice (excessive for information, low for command) |
| RST | Exterior reset, low lively |
| BUSY | Busy standing output, low lively |
That is an E-Ink show HAT for Raspberry Pi, 2.13inch, 212×104 decision, with an embedded controller, speaking through SPI interface, helps the pink, black, and white three-colour show.
There isn’t a backlight so it could actually hold displaying the final content material for a very long time even when the facility is down. As these shows haven’t any backlight panels and it doesn’t want a steady energy provide to show the (static information with periodic intervals) information on the display screen, it has a terrific benefit of ultra-low energy consumption. Additionally, it has a large viewing angle, nice viewing impact below daylight, principally, energy to the show is just required for refreshing. For connecting with controller boards like Raspberry Pi/Arduino/Nucleo, and so on. SPI interface can be utilized.2.13 Inch 3 color show E-Paper Hat (B) is an E-Ink show HAT for Raspberry Pi 2.13 inch, 212×104 decision, with embedded controller and speaking through SPI interface. This show helps pink, black, and white three-colour show.
As a result of advantages like ultra-low energy consumption, vast viewing angle, the great impact below daylight, it is an ideal selection for purposes like shelf label, industrial instrument, and so forth. Options No backlight, retains displaying final content material for an prolonged time even when energy down Extremely-low energy consumption, principally energy is merely required for refreshing Suitable with Raspberry Pi 2B/3B/Zero/Zero W Preserved solder pads for SPI interface, for connecting with different controller boards like Arduino/Nucleo, and so on. Comes with growth assets and guide examples for Raspberry/Arduino/STM32) Specs Working voltage: 3.3V Interface: SPI Define dimension: 65mm? 30.2mm Show dimension: 23.71mm? 48.55mm Dot pitch: 0.194 ? 0.194 Decision: 250 ? 122 Show color: black, white Gray degree: 2 Refresh energy: 26.5mV(typ.) Standby energy: 170ø
